Difference between revisions of "Template:FriendlyWrt19"

From FriendlyARM WiKi
Jump to: navigation, search
(Work with USB WiFi Device)
(Work with USB WiFi Device)
Line 42: Line 42:
 
===Work with USB WiFi Device===
 
===Work with USB WiFi Device===
 
====Check USB WiFi Device with Command Line Utility====
 
====Check USB WiFi Device with Command Line Utility====
(1) Click on "service>ttyd" to start the command line utility<br />
+
(1) Click on "services>ttyd" to start the command line utility<br />
 
[[File:R2s-wrt-jellyfin-002.jpg|frameless|800px]]<br />
 
[[File:R2s-wrt-jellyfin-002.jpg|frameless|800px]]<br />
  
Line 65: Line 65:
 
<span style="color: blue; ">Note: devices that match these VID&PIDs would most likely work.</span>
 
<span style="color: blue; ">Note: devices that match these VID&PIDs would most likely work.</span>
  
(2) Click on "System>Reboot/Restart" and reboot your NanoPi R2S<br />
+
(2) Click on "System>Reboot" and reboot your NanoPi R2S<br />
 
[[File:R2swrt+usbwifi-01.jpg|frameless|800px]]<br />
 
[[File:R2swrt+usbwifi-01.jpg|frameless|800px]]<br />
 
<br />
 
<br />
Line 76: Line 76:
 
[[File:R2swrt+usbwifi-04.jpg|frameless|800px]]<br />
 
[[File:R2swrt+usbwifi-04.jpg|frameless|800px]]<br />
  
(5) On the "接口配置" page you can set the WiFi mode and SSID, and then go to "Wireless Security" to change the password. By default the password is "password". After you make your changes click on "Save" to save<br />
+
(5) On the "Interface Configuration" page you can set the WiFi mode and SSID, and then go to "Wireless Security" to change the password. By default the password is "password". After you make your changes click on "Save" to save<br />
 
[[File:R2swrt+usbwifi-05.jpg|frameless|800px]]<br />
 
[[File:R2swrt+usbwifi-05.jpg|frameless|800px]]<br />
 
<br />
 
<br />

Revision as of 05:07, 19 November 2020

1 Work with FriendlyWrt

1.1 Introduction to FriendlyWrt

FriendlyWrt is a customized system made by FriendlyElec based on an OpenWrt distribution. It is open source and well suitable for developing IoT applications, NAS applications, smart home gateways etc.

1.2 Account & Password

By default the password is NULL. You can set a password for root for web and SSH login.

1.3 Network Connection

Use a network cable to connect {{{1}}}'s WAN to a master router and the board will get an IP address via DHCP. Login into the router and check {{{1}}}'s IP address.

1.4 Login FriendlyWrt

Type {{{1}}}'s IP address or http://friendlywrt/ in a browser's address bar and enter to open FriendlyWrt's administration page or you can login into FriendlyWrt's administration page via SSH.
By default, the IP address of the LAN port is 192.168.2.1, and the WAN will dynamically obtain the IP address from your main router.

1.5 Install Software Packages

1.5.1 Update Package List

Before install software packages update the package list:

$ opkg update

1.5.2 List Available Packages

$ opkg list

1.5.3 List Installed Packages

$ opkg list-installed

1.5.4 Install Packages

$ opkg install <package names>

1.5.5 Remove Packages

$ opkg remove <package names>

1.6 Work with USB WiFi Device

1.6.1 Check USB WiFi Device with Command Line Utility

(1) Click on "services>ttyd" to start the command line utility
R2s-wrt-jellyfin-002.jpg

(2) Make sure no USB devices are connected to your board and run the following command to check if any USB devices are connected or not

lsusb

R2swrt+usbwifi-09.jpg

(3) Connect a USB WiFi device to the board and run the command again

lsusb

You will see a new device is detected. In our test the device's ID was 0BDA:C811
R2swrt+usbwifi-10.jpg

(4) Type your device's ID (in our case it was "0BDA:C811" or "VID_0BDA&PID_C811") in a search engine and you may find a device that matches the ID. In our case the device we got was Realtek 8811CU.

1.6.2 Configure a USB WiFi Device as AP

(1) Connect a USB WiFi device to the NanoPi R2S. We recommend you to use the following devices which we have tested with FriendlyElec's rk3328-sd-friendlywrt-5.4-20200514.img file
R2swrt+usbwifi-08.jpg
Note: devices that match these VID&PIDs would most likely work.

(2) Click on "System>Reboot" and reboot your NanoPi R2S
R2swrt+usbwifi-01.jpg

R2swrt+usbwifi-02.jpg

(3) Click on "Network>Wireless" to enter the WiFi configuration page
R2swrt+usbwifi-03.jpg

(4) Click on "Edit" to edit the configuration
R2swrt+usbwifi-04.jpg

(5) On the "Interface Configuration" page you can set the WiFi mode and SSID, and then go to "Wireless Security" to change the password. By default the password is "password". After you make your changes click on "Save" to save
R2swrt+usbwifi-05.jpg

R2swrt+usbwifi-06.jpg

(6) After you change the settings you can use a smartphone or PC to search for WiFi
R2swrt+usbwifi-07.png

1.7 Work with Docker Applications

1.7.1 Work with Docker: Install JellyBin

mkdir -p /jellyfin/config
mkdir -p /jellyfin/videos
docker run --restart=always -d -p 8096:8096 -v /jellyfin/config:/config -v /jellyfin/videos:/videos jellyfin/jellyfin:10.1.0-arm64 -name myjellyfin

After installation, visit port 8096 and here is what you would find:
FriendlyWrt+JerryFin

1.7.2 Work with Docker: Install Personal Nextcloud

mkdir /nextcloud -p
docker run -d -p 8888:80  --name nextcloud  -v /nextcloud/:/var/www/html/ --restart=always --privileged=true  arm64v8/nextcloud

After installtion, visit port 8888.

1.8 Enable Swap Partition

Run the following commands in a commandline utility and reboot:

/etc/enable-swap.sh
reboot

1.9 Mount smbfs

mount -t cifs //192.168.1.10/shared /movie -o username=xxx,password=yyy,file_mode=0644


1.10 Compile u-boot,kernel or friendlywrt