Difference between revisions of "NanoHat OLED for NanoPi NEO2 Black/zh"

From FriendlyARM WiKi
Jump to: navigation, search
(硬件连接)
Line 60: Line 60:
 
[[File:NanoHat OLED_NanoPi_NEO2_Black.jpg|frameless|500px|NanoHat_OLED_NanoPi_NEO2_Black]]
 
[[File:NanoHat OLED_NanoPi_NEO2_Black.jpg|frameless|500px|NanoHat_OLED_NanoPi_NEO2_Black]]
  
==使用默认使能NanoHat OLED for NanoPi NEO2 Black的ROM==
+
==ROM That Enables Support for NanoHat OLED for NanoPi NEO2 Black==
 
::{| class="wikitable"
 
::{| class="wikitable"
 
|-
 
|-
Line 69: Line 69:
 
|}
 
|}
  
==手动使能NanoHat OLED for NanoPi NEO2 Black==
+
==Manually Enable Support for NanoHat OLED for NanoPi NEO2 Black==
NanoHat OLED for NanoPi NEO2 Black的演示程序包含在 NanoHatOLED 软件仓库里,启动系统,执行以下命令进行安装:<br />
+
FriendlyElec developed code samples for the NanoHat OLED for NanoPi NEO2 Black and these code samples are contained in the NanoHatOLED's github. You can download and install these code samples by running the following commands after you boot a NanoPi NEO2 Black:<br />
 
<syntaxhighlight lang="bash">
 
<syntaxhighlight lang="bash">
 
git clone https://github.com/friendlyarm/NanoHatOLED.git
 
git clone https://github.com/friendlyarm/NanoHatOLED.git

Revision as of 08:32, 7 January 2020

English

1 Introduction

NanoHat OLED for NanoPi NEO2 Black
Front
Back
  • The NanoHat OLED for NanoPi NEO2 Black module is a monochrome OLED module designed and developed for the NanoPi NEO2 Black. It is 0.96" and the resolution is 128 x 64. It has high contrast and low power-consumption. It can display characters and images. It communicates with a NanoPi NEO2 Black with I2C.
  • The size of the NanoHat OLED for NanoPi NEO2 Black is the same as the size of the NanoPi NEO2 Black. The OLED module can be stacked onto a NanoPi NEO2 Black.
  • The module has three programmable keys.
  • The module has a 3.5mm audio jack and a USB Type A port.

2 Hardware Spec

  • Size: 0.96"
  • Resolution: 128 x 64
  • High contrast and low power consumption
  • 3 x onboard key
  • PCB dimension(mm): 40 x 40

NanoHat OLED for NanoPi NEO2 Black PCB

  • GPIO1(I2C/UART/GPIO)
Pin# Name Linux gpio Pin# Name Linux gpio
1 GPIOA0 0 2 5V in or out -
3 I2C_SDA0 - 4 5V in or out -
5 I2C_SCL0 - 6 GND -
7 GPIOA2 2 8 UART1_TX -
9 GND - 10 UART1_RX -
  • GPIO2(USB/Audio OUT)
Pin# Name Linux gpio Pin# Name Linux gpio
1 Line out Right - 2 USB DM -
3 Line out Left - 4 USB DP -
5 Audio GND - 6 GPIOA3 3

3 Applicable Board & OS

Index CPU Model Board Type OS
1 H5 NanoPi NEO2 Black Open Source Linux-4.x Mainline Kernel

4 Hardware Setup

The size of the NanoHat OLED for NanoPi NEO2 Black is the same as the size of the NanoPi NEO2 Black. The module can be stacked onto a NanoPi NEO2 Black. Here is a hardware setup:
NanoHat_OLED_NanoPi_NEO2_Black

5 ROM That Enables Support for NanoHat OLED for NanoPi NEO2 Black

Board Type CPU Model Download Link to Image File Image File
NanoPi NEO2 Black H5 Download official-ROMs/accessory-ROMs/nanopi-neo2-black_ubuntu-oled_4.x.y_YYYYMMDD.img.zip

6 Manually Enable Support for NanoHat OLED for NanoPi NEO2 Black

FriendlyElec developed code samples for the NanoHat OLED for NanoPi NEO2 Black and these code samples are contained in the NanoHatOLED's github. You can download and install these code samples by running the following commands after you boot a NanoPi NEO2 Black:

git clone https://github.com/friendlyarm/NanoHatOLED.git
cd NanoHatOLED
sudo -H ./install.sh


安装脚本会在线下载并安装一系列的软件包,安装时间视网络环境而定,国内大陆的用户为了获得更快的安装速度,可以在安装之前先将软件包的源设置为国内源,执行以下命令,使用我们提供的脚本进行设置:

wget http://112.124.9.243/aptsouce.sh
chmod 755 aptsouce.sh
sudo -H ./aptsouce.sh
sudo apt-get update

操作完成后,再执行NanoHatOLED的 ./install.sh 安装脚本安装即可。

7 演示程序的操作说明

演示程序在安装后会在开机时自动运行,并默认显示 日期与时间 画面。
NanoHat OLED配件上的三个按键功能如下:
K1 -> 显示日期时间;
K2 -> 显示开发板的运行状态,例如 IP地址, 负载, 存储状态,CPU温度等信息;
K3 -> 关机操作,并不会立即关机,而是先弹出询问画面,在询问画面的状态下,用 K1 切换 Yes和No选项,K2进行确认;

8 相关资料