Power Dock for NanoPi NEO

From FriendlyARM WiKi
Jump to: navigation, search

查看中文

Introduction

Power Dock for NanoPi NEO
  • The Power Dock for NanoPi NEO is a power conversion board.
  • It uses TI's TPS54331 device with wide voltage range.TPS54331 integrates a low RDS(on) high-side MOSFET.
  • Its slow-start feature limits inrush currents. Its overvoltage transient protection circuit limits voltage overshoots during startup and transient conditions.
  • Its side A has double-layer tall female connectors which allow a NEO to be stacked on the board. Its side B populates NEO's GPIO pins.

Hardware Spec

  • Input Voltage: 12V
  • Output: 5V/2A
  • Switching Frequency: 570KHz
  • Shutdown Quiescent Current: 1uA
  • Under Voltage Lockout
  • Overvoltage Protection
  • Slow-Start
  • PCB dimension(mm): 40 x 88

Power Dock for NanoPi NEO_PCB

  • Pin Description:
  • GPIO Pin Description
Pin# Name Linux gpio Pin# Name Linux gpio
1 SYS_3.3V 2 VDD_5V
3 I2C0_SDA 4 VDD_5V
5 I2C0_SCL 6 GND
7 GPIOG11 203 8 UART1_TX/GPIOG6 198
9 GND 10 UART1_RX/GPIOG7 199
11 UART2_TX/GPIOA0 0 12 PWM1/GPIOA6 6
13 UART2_RTS/GPIOA2 2 14 GND
15 UART2_CTS/GPIOA3 3 16 UART1_RTS/GPIOG8 200
17 SYS_3.3V 18 UART1_CTS/GPIOG9 201
19 SPI0_MOSI/GPIOC0 64 20 GND
21 SPI0_MISO/GPIOC1 65 22 UART2_RX/GPIOA1 1
23 SPI0_CLK/GPIOC2 93 24 SPI0_CS/GPIOC3 67
  • USB/Audio/IR Pin Description
NanoPi-NEO V1.1
Pin# Name Description
1 VDD_5V 5V Power Out
2 USB-DP1 USB1 DP Signal
3 USB-DM1 USB1 DM Signal
4 USB-DP2 USB2 DP Signal
5 USB-DM2 USB2 DM Signal
6 GPIOL11/IR-RX GPIOL11 or IR Receive
7 SPDIF-OUT/GPIOA17 GPIOA17 or SPDIF-OUT
8 PCM0_SYNC/I2S0_LRC I2S/PCM Sample Rate Clock/Sync
9 PCM0_CLK/I2S0_BCK I2S/PCM Sample Rate Clock
10 PCM0_DOUT/I2S0_SDOUT I2S/PCM Serial Bata Output
11 PCM0_DIN/I2S0_SDIN I2S/PCM Serial Data Input
12 GND 0V

Device Operation

  • The Power Dock for NanoPi NEO uses TI's TPS54331 device. The TPS54331 device is a 28-V, 3-A non-synchronous buck converter that integrates a low RDS(on) high-side MOSFET.

Hardware Setup

Connect Power Dock to NanoPi NEO

A NanoPi NEO can be stacked on the board at side A's female connector. Its side B populates NEO's GPIO pins.

Hardware Setup
Power Dock for NanoPi NEO_nanopi_NEO
Connect Power Dock to NanoPi BAT & Other Modules:
Power Dock for NanoPi BAT Power Dock for NanoPi NEO Hub Power Dock for NanoPi RTC Power Dock for NanoPi GPS

Resources

Update Log

April-19-2017

  • Released English version